Dark Light

PSA  AUTOMATIC

Bosh EDC17C60


Instruction manual

 
 
 
 
 The Emulator allows you to read the ECU’s PIN CODE or turn OFF immobiliser. The procedure must be  completed by connecting the ECU on the bench. You just need to connect the Emulator to the ECU according to the pinout shown below. The Emulator will automatically determine the ECU’s PIN CODE or replace immobiliser signal. The procedure may take 3 to 90 hours. Procedure completion will be indicated by a blue LED on the Emulator.

 



CONNECTION

  Program Usage

 

The emulator will automically establish the ECU’s PIN CODE in 3 to 90 hours or it will allow you to start the car, which will be indicated by a blue 

Example cars

CITROEN 
Citroen Berlingo 
Citroen C4 Cactus
Citroen C5 AirCross
Citroen Jumpy 
DS7


PEUGEOT

208 II 
308 II
3008
OPEL
Crossland X



  1. Procedure

Based on pinouts above, connect the ECU on the bench using laboratory power supply and dedicated wires. Solder the Emulator jumpers 
( 1 + 2 + 3 + 5  + 7)

Sample Image

2. Procedure

Connect the Emulator wires to the ECU according to the pinout.
Connect the Emulator to the ECU power supply wires ( DETERMINIG PIN ) or solder directly to the 
ECU ( IMMO OFF )

Sample Image


  Blue LED Behaviour

  Info

LOOKING FOR CODE
0,1 sec ON
2,0 sec OFF

Turn the power ON. The Emulator will start searching for the code. 
This procedure may take 3 to 90 hours.
IMPOTANT: If you turn the power OFF, the procedure will be paused
-the Emulator will NOT reset itself.This  means that when you turn the power ON again, the procedure will continue right from the place it was stpped at

CODE FOUND, VERIFYING FOR 10 SEC 
0,2  sec ON
0,2 sec OFF

  The Emulator found a passible match – it proceeds to verify the code for 10 seconds. If the code is found, the procedure will be complete.
Otherwise, the Emulator will resume searching for the code.

CODE FOUND, PROCEDURE COMPLETE
2,0 sec ON
0,1 sec OFF

  The Emulator succesflly determined the PIN code – the car is allowed to start. The PIN code can be found on the Emulator’s 24C02 memory.

CONNECTION WİTH ECU NOT ESTABLISHED
0,1 sec ON
0,1 sec OFF

  Check the POWER or CAN line


Determine the PIN CODE of the ECU

 After the procedure above is complete and the blue LED indicates that the PIN code has been determinedcorrectly, disconnect the Emulator from the ECU, unsolder 24C02 memory and read its content with a programmer. PIN CODE will be saved in the TEXT section.

  ATTENTION !

  • The Emulator is reusable
  • You can determine the PIN CODE or turn OFF the immobiliser in anther ECU
  •   You can use PIN CODE to code the key or match the ECU to the car.
 

 Program introduction

 

 The Emulator a llows you to read the ECU’s PIN CODE or turn OFF immobiliser. The procedure must be  completed by connecting the ECU on the bench. You just need to connect the Emulator to the ECU according to the pinout shown below. The Emulator will automatically determine the ECU’s PIN CODE or replace immobiliser signal. The procedure may take 3 to 90 hours. Procedure completion will be indicated by a blue LED on the Emulator.
 
IMMO OFF 
After the procedure above is complete and the blue LED indicates that the PIN code has been determined correctly, disconnect the Emulator from the ECU, open the Emulator cover using utility knife and solder the jumpers: 1 + 2 + 4 + 5 + 6. Then solder together leg 7 and 8 of the Emulator’s 24C02 memory

  ATTENTION !

  The Emulator is resable
  In order to use it on another ECU, remove the solder bridge between leg 7 and 8 of the 24C02 memory and change the jumpers back to 1 + 2 + 3 + 5 + 7

  After the ignition is turned on for the first time, the Emulator will check the correctness of the code. If it’s not correct the Emulator will restart the scanning procedure

Any attempt at larceny, copying, citing or reselling the disclosed ideas, images and graphics in the instruction developed by us & without permission is strictly prohibited.
All afore mentioned are subject to and protected concordantly by the 4.I. 1994 enactment respecting copyright and affined laws (Dz.U. nr 24 poz. 93) + protection of the 8.VI. 1993 enactment regarding eradicating dishonest competition (Dz.U. nr 47 poz. 211).
Not applying to the conditions specified above will be met with penal consequences!
This company is not liable for the device being used for illegal purposes.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.

Open chat
Hello 👋
Can we help you?